YOKE
Using larger 16-inch circular
needle, CO 64[72, 76, 84,
88, 96, 104] sts. Place marker
and join to begin working
in the round, being careful
not to twist [use the stitch
marker which is different
from the others].
As yoke
is worked, switch to longer circular
needle when necessary.
Set-up Round: K21[23, 25, 29, 31, 35, 39] for front,
place marker, k11[13, 13, 13, 13, 13, 13] for left sleeve,
place marker, k21[23, 25, 29, 31, 35, 39] for back, place
marker, k11[13, 13, 13, 13, 13, 13] for right sleeve.
Increase Round: [Kfb, k to 1 st before marker, kfb]
four times. 8 sts increased.
Next Round: [K1, p1] to
end.
Repeat these 2 rounds 17[20,
23, 25, 29, 31, 33] times more. 208[240, 268, 292, 328,
352, 376] sts: front and back each have 57[65, 73, 81,
91, 99, 107] sts, each sleeve has 47[55, 61, 65, 73,
77, 81] sts.
Note: When working dividing round, you will be directed
to cast on sts at each underarm. Cast on these sts using
the cable cast on method (see Pattern Notes), as follows:
before casting on sts, turn work so WS is facing. CO
sts as directed, then turn work so that RS is facing
again before proceeding.
Dividing Round: K to first marker, remove marker, slip
last st worked to left needle, place marker on right
needle, slip st back to right needle; place next 47[55,
61, 65, 73, 77, 81] sts (all sts to next marker) on waste
yarn for left sleeve, remove marker, CO 3 sts, k1, place
marker (5 sts between markers); k to next marker, remove
marker, slip last st worked to left needle, place marker
on right needle, slip st back to right needle; place
next 47[55, 61, 65, 73, 77, 81] sts (all sts to end-of-round
marker) on waste yarn for right sleeve, remove marker,
CO 3 sts, k1, place marker (5 sts between markers). 120[136,
152, 168, 188, 204, 220] sts.
LOWER BODY
Next Round: Work in Relaxed Rib Pattern to first
marker, work Left Cable, work in Relaxed Rib Pattern to
third marker, work Right Cable.
This round sets pattern
for lower body.
Continue in pattern until work measures approx. 6.5[7,
8.5, 8.5, 8.5, 8.5, 8.5] inches from Dividing Round,
ending with Round 1 of Relaxed Rib Pattern.
Note: When shaping lower body, two increase rounds are
worked at a time, one right after the other. This is
done to maintain the stitch pattern.
Increase Round: [P1, M1L,
work in pattern to 1 st before marker, M1R, p1, work
next round of cable pattern] twice.
Repeat Increase Round.
Work 7 rounds in pattern.
Repeat these 9 rounds 1[1,
1, 2, 2, 2, 2] times more. 136[152, 168, 192, 212, 228,
244] sts.
Continue in pattern until work measures 10.75[12.5,
13.5, 14.5, 15.5, 15.5, 16.5] inches from underarm or
0.5 inch shorter than desired length.
Next Round: Using smaller long circular needle, [p1,
(k1, p1) to marker, k2, p1, k2] twice.
Repeat this round twice
more. BO all sts using Picot Bind Off.
LEFT SLEEVE
Place held sts of left sleeve on 16-inch
circular needle. With RS facing and beginning at right
edge of CO underarm sts, pick up and k 5 sts (1 st in
each CO st and 1 st at each edge), place marker, work
47[55, 61, 65, 73, 77, 81] sts of sleeve in Relaxed Rib,
place marker to indicate beginning of round, join to
work in the round. 52[60, 66, 70, 78, 82, 86] sts.
Work 7 rounds in pattern,
working Left Cable over 5 sts between markers and Relaxed
Rib over all other sts.
End with Round 1 of Relaxed Rib
Pattern.
Note: When shaping sleeve, two decrease rounds are worked
at a time, one right after the other. This is done to
maintain the stitch pattern. Switch to double-point needles
when necessary.
Decrease Round: Work next
round of cable pattern, p1, k2tog, work in pattern to
3 sts before marker, ssk, p1.
Repeat Decrease Round.
Work 7 rounds in pattern.
Repeat these 9 rounds 3[4,
5, 5, 5, 5, 5] times more, then work Decrease
Round twice
more. 32[36, 38, 42, 50, 54, 58] sts.
Continue in pattern until sleeve measures 7.5[8.75,
8.75, 10.25, 10.25, 10.75, 10.75] inches from underarm,
or 1.25 inches less than desired length.
Next Round: Work next round of cable pattern, work 3[4,
2, 4, 2, 4, 3] sts in pattern, m1, [work 7[6, 6, 6, 7,
7, 8] sts in pattern, m1] 3[4, 5, 5, 6, 6, 6] times,
work in pattern to end of round. 36[41, 44, 48, 57, 61,
65] sts.
Next Round: Work next round
of cable pattern, work 3[4, 2, 4, 2, 4, 3] sts in pattern,
m1, [work 8[7, 7, 7, 8, 8, 9] sts in pattern, m1] 3[4,
5, 5, 6, 6, 6] times, work in pattern to end of round.
40[46, 50, 54, 64, 68, 72] sts.
Work 3 more rounds in pattern.
Next Round: [K2, p1] twice,
(k1, p1) to end of round.
Repeat this round twice
more. BO all sts using Picot Bind Off.
RIGHT SLEEVE
Work as for left sleeve, working Right Cable
instead of Left Cable.
|